- Cat C27 Part Manual Diagram
- Caterpillar C27
- Part Lookup - Cat® Parts Store - Order Cat® Parts Online
- Cat C27 Part Manual Download
- Caterpillar C7 - C9 Engine Manual & Parts Catalog
Cat C27 Part Manual Diagram
INSTANT DOWNLOAD (add to cart)
Complete workshop & service manual with electrical wiring diagrams for Caterpillar C27 & C32 Engines. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page.
This Caterpillar C27 & C32 Engines service & repair manual (including maintenance, overhaul, disassembling & assembling, adjustment, tune-up, operation, inspecting, diagnostic & troubleshooting…) is divided into different sections. Each section covers a specific component or system with detailed illustrations. A table of contents is placed at the beginning of each section. Pages are easily found by category, and each page is expandable for great detail. The printer-ready PDF documents work like a charm on all kinds of devices.
Models: DWB1-UP, SXC1-UP, MED1-UP, WDR1-UP This is the most complete service repair manual for Cat C27 and C32 Generator Set Engine. This manual contains service, repair procedures, assembling, disassembling, wiring diagrams and everything you need to know.
INSTANT DOWNLOAD (add to cart) Complete workshop & service manual with electrical wiring diagrams for Caterpillar C27 & C32 Engines. It’s the same service manual used by dealers that guaranteed to be fully functional and intact without any missing page. Caterpillar C27 Parts Manual Industrial Engine, 1206 pages - click to download Diesel Engine Specs Basic specs are free and open to everyone They usually include engine images, displacement, dimensions and weight, essential bolt tightening torques, plus characteristics of the engine e.g. Its power and torque. C27 ACERT® PETROLEUM ENGINE 596-782 bkW (800-1050 bhp) LEHW0052-00. Page.3.of.4 PERFORMANCE CURVES Turbocharged-Aftercooled D Rating — 783 bkW (1050 bhp) @ 2100 rpm.
MANUAL LIST:
KENR5930 – Schematic (C32 Generator Set with EMCP II+P Electrical System)
KENR9912 – Systems Operation (C27 & C32 Tier 4 Engines)
KENR9912 – Testing & Adjusting (C27 & C32 Tier 4 Engines)
M0074364 – Disassembly & Assembly (C27 & C32 Engines)
RENR7167 – Specifications (C27 & C32 Generator Set Engines)
RENR9716 – Disassembly & Assembly – (C27 & C32 Generator Set Engines)
RENR9855 – Schematic (C32 Generator Set with EMCP 3 Electrical System 292-4084-03)
RENR9968 – Systems Operation (C27 & C32 Generator Set Engines)
RENR9968 – Testing & Adjusting (C27 & C32 Generator Set Engines)
SENR5359 – Disassembly & Assembly (SR4B Generators)
SENR5359 – Systems Operation (SR4B Generators)
SENR5359 – Testing & Adjusting (SR4B Generators)
UENR0504 – Troubleshooting (C27 & C32 Tier 4 Engines)
UENR1204 – Schematic (Electrical System of C27 & C32 Industrial Engine_Petroleum Engine_Locomotive Engine (363-4591-04, 421-4298-00)
KENR9885 – Specifications (C27 & C32 Engines for Caterpillar Built Machines)
KENR9886 – Systems Operation (C27 & C32 Engines for Caterpillar Built Machines)
KENR9886 – Testing & Adjusting (C27 & C32 Engines for Caterpillar Built Machines)
RENR9217 – Disassembly & Assembly (C27 & C32 Engines for Caterpillar Built Machines)
UENR0517 – Troubleshooting (C32 LRC Engine for Track-Type Tractors)
KENR5930 – Schematic (C32 Generator Set with EMCP II+P Electrical System)
KENR9912 – Systems Operation (C27 & C32 Tier 4 Engines)
KENR9912 – Testing & Adjusting (C27 & C32 Tier 4 Engines)
M0074364 – Disassembly & Assembly (C27 & C32 Engines)
RENR7167 – Specifications (C27 & C32 Generator Set Engines)
RENR9716 – Disassembly & Assembly – (C27 & C32 Generator Set Engines)
RENR9855 – Schematic (C32 Generator Set with EMCP 3 Electrical System 292-4084-03)
RENR9968 – Systems Operation (C27 & C32 Generator Set Engines)
RENR9968 – Testing & Adjusting (C27 & C32 Generator Set Engines)
SENR5359 – Disassembly & Assembly (SR4B Generators)
SENR5359 – Systems Operation (SR4B Generators)
SENR5359 – Testing & Adjusting (SR4B Generators)
UENR0504 – Troubleshooting (C27 & C32 Tier 4 Engines)
UENR1204 – Schematic (Electrical System of C27 & C32 Industrial Engine_Petroleum Engine_Locomotive Engine (363-4591-04, 421-4298-00)
KENR9885 – Specifications (C27 & C32 Engines for Caterpillar Built Machines)
KENR9886 – Systems Operation (C27 & C32 Engines for Caterpillar Built Machines)
KENR9886 – Testing & Adjusting (C27 & C32 Engines for Caterpillar Built Machines)
RENR9217 – Disassembly & Assembly (C27 & C32 Engines for Caterpillar Built Machines)
UENR0517 – Troubleshooting (C32 LRC Engine for Track-Type Tractors)
Foxboro 40p pneumatic controller manual. EXCERPT:
2. Position alternator (6). Position guard (7) and install bolts (5). Connect harness assembly (3). Connect ground strap (4). Install bolt (1). Connect cable assembly (2).
3. Install the V-belt on the engine.
4. Turn the battery disconnect switch to the ON position.
…
2. Position alternator (6). Position guard (7) and install bolts (5). Connect harness assembly (3). Connect ground strap (4). Install bolt (1). Connect cable assembly (2).
3. Install the V-belt on the engine.
4. Turn the battery disconnect switch to the ON position.
…
Category: Manual
Usage:
826K2L3Caterpillar C27
Removal Procedure
![Caterpillar C7 - C9 engine Manual & Parts Catalog Caterpillar C7 - C9 engine Manual & Parts Catalog](https://www.repairmanual.com/wp-content/uploads/Caterpillar-112-Motor-Grader-Parts-Manual_Page_5.jpg)
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 5F-4764 | Pry Bar | 1 |
B | 8T-2998 | Lubricant | 1 |
C | 1U-5718 | Vacuum Pump | 1 |
169-7372 | Fluid Sampling Bottle | 1 | |
4C-4057 | Tube | 1 | |
D | 4C-5552 | Large Bore Brush | 1 |
E | 4C-6774 | Vacuum Gun Kit | 1 |
F | 8T-7765 | Surface Reconditioning Pad | 1 |
Start By:
- Remove the rocker arms and the rocker arm shaft.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. |
Part Lookup - Cat® Parts Store - Order Cat® Parts Online
- Disconnect harness assembly (1).
- Remove bridge assemblies (3). Show/hide table
NOTICE If the injector hold down bolt is loose during the removal procedure, inspect the injector bore for wear and debris. Replace the clamp and spacer. - Remove bolt (4) and spacer (5).
- Place an identification mark on electronic unit injectors (2) for installation purposes. Each electronic unit injector must be reinstalled in the original location in the cylinder head.
- Use Tooling (A) to pry beneath the base of clamp (6) and free electronic unit injector (2).
- Remove clamp (6) and electronic unit injector (2) from the cylinder head.
Illustration 1 | g02343936 |
Installation Procedure
Cat C27 Part Manual Download
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. S mime reader for mac. |
Caterpillar C7 - C9 Engine Manual & Parts Catalog
- Use Tooling (C) to remove the fuel and oil from the cylinder. Evacuate as much fuel and oil as possible from the cylinder before installing the electronic unit injector. Several evacuations may be necessary.
- Use Tooling (D) to clean the carbon deposit from the inside of the electronic unit injector sleeve. Tooling (E) is available to clean loose material from the bore of the electronic unit injector sleeve and the cylinder.
- Use Tooling (F) to clean the carbon from the seat area that is inside of the electronic unit injector sleeve.
- Install the O-ring seals on the electronic unit injector. Lubricate the top two O-ring seals with a 50/50 mixture of clean engine oil and Tooling (B). Show/hide table
Illustration 2 g02343936 Illustration 3 g01135876 - The E-Trim value must be programmed into the engine control module when you install a new injector . Program the injector confirmation code into the engine control module. E-Trim Value (X) is a 12 digit alphanumeric code that is supplied with the data sheet that comes with the new injectors. Injector Confirmation Code (Y) is a four digit numeric code. Both of the codes are located on the top of electronic unit injector (2). Use the following menu to program the E-Trim value.
- ECM Summary Screen
- Service Menu
- Calibration
- Injector Code Calibration
Show/hide tableNOTICE When an electronic unit injector is replaced, the new electronic injector code must be programmed into the engine's personality module software by using the calibration menu on the Electronic Service Tool. If the new electronic injector code is not entered, the characteristics of the previous electronic unit injector is assumed.If it is not possible to immediately reprogram the electronic injector code into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance. - Position electronic unit injector (2) and clamp (6) in the cylinder head.
- Install spacer (5) and bolt (4). Tighten the bolt to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . - Install bridge assemblies (3).
- Connect harness assembly (1).
End By:
- Install the rocker arms and the rocker arm shaft.